- Stereo Power Amplifier
300BPA
- Vacuum tube stereo power amplifier featuring the direct-heating triode 300B, with an output of 9W+9W. In bridge connection it can also be used as a 20W monaural amplifier. A pure non-feedback design with built-in input transformers delivers clarity and spatial realism.
- Silence and clear low-level signals
- Doubly regulated power supply
- Large output transformers
Features
- Silence and clear low-level signals
- Drawing on CS Port’s noise control technology, residual noise is held to 200 μV or less across the entire 20 Hz–20 kHz audio band. Measured with standard A-weighting, the figure is 20 μV: audibly very quiet, so the position of each instrument is reproduced vividly.
【Output tube options】
The 300B output tubes are available from three brands. A model supplied without output tubes is also available.
| Output tube | Model |
|---|---|
| TAKATSUKI TA-300B | 300BPA-TA |
| Western Electric 300B | 300BPA-WE |
| JJ Electronic 300B | 300BPA-JJ |
| No output tubes | 300BPA-00 |
【Three operating modes】
Selected with the rear switch.
○ Normal: 9W+9W (stereo)
○ Dual mono: 9W+9W
○ Bridge: 20W (monaural)
* Dual mono and bridge are available with the Lch XLR input.
- Two-stage with C3g
- Uses the ultra-reliable C3g tube, developed by Deutsche Telekom, in triode connection. Its fine grid wires and wide electrode spacing give highly linear amplification. Using only two tubes, an input tube and the output tube, harmonics and intermodulation distortions are kept low through a non-feedback design.
- Large output transformers
- Multilayer sandwich winding provides wide bandwidth drive from small to large signals. Low winding resistance and strong drive capability give a high damping factor for a non-feedback amplifier, for reliable low-frequency drive.
- Doubly regulated power supply
- The rectifiers and contacts in conventional power supplies generate sharp noise from 50 Hz up to several hundred MHz, clouding the sound. Drawing on our half-century of knowledge in power supply development, we developed a switching power supply optimized for audio applications. Double regulation by the switching and analog power supplies provides quiet, noise-free output.
Specification
Model 300BPA-TA / 300BPA-WE / 300BPA-JJ / 300BPA-00
Type
Class-A vacuum tube stereo power amplifier with built-in input transformers
Output Power
○ Normal, Dual mono
9 W+9 W (THD5%)
○ Bridge
20 W (THD5%)
Frequency Response
20 Hz-70 kHz -2 dB
THD
1%/1.5 W
NFB
None
Residual Noise
20 μV (A-weighted) / 200 μV (unweighted) 20 Hz-20 kHz
Signal to Noise Ratio
-85 dB
Crosstalk
-50 dB
Input Sensitivity
1.2 V
Gain
17 dB (4 Ω) 20 dB (8 Ω)
Input Terminal
XLR (balanced, pin 2 hot) ×1 RCA (unbalanced) ×1
Input Impedance
5 kΩ
Mode Switching
By the rear switch
Volume Adjustment
None
Output Terminals
0-4-8 Ω
Damping Factor
3.35 (4 Ω) 3.5 (8 Ω)
Power Supply
AC100/120/200/240 V, 50/60 Hz
Power Consumption
120 W
Dimensions
234W×200H×420D mm
Weight
14 kg
Finishing
Anodized aluminum
Accessories
Rhodium-plated AC cord
Warranty Period
5 years
○ The input impedance of this unit is 5 kΩ. Please use source equipment with an output impedance of 2 kΩ or less.
○ The 300B output tubes can be selected from three brands: TAKATSUKI, Western Electric, and JJ Electronic. A model without 300B tubes (Model: 300BPA-00) is also available.
○ Vacuum tubes are treated as consumables and are not covered by warranty.
○ Do not touch the vacuum tube as it is hot and may cause burns.
○ Dimensions include legs but do not include knobs or terminals.
○ The descriptions are current as of October 2026.
○ The appearance and specifications are subject to change without notice.
○ Actual colors may differ from those in the photographs due to photography and lighting conditions.